GetFPV
LC COMMON MODE POWER FILTER
| Revision | Rev3 March 2013 |
| Type | passive common-mode low-pass power ripple filter |
| Modes | common mode, single mode - jumper selectable |
| Maximum voltage | 16V DC |
| Maximum current | ~1.5A |
| Cutoff frequency at -3dB | 127 Hz (attenuates higher frequencies/noise) |
| Voltage drop over filter | 180mV at 900mA |
| Maximum voltage ripple | 120mV |
| Capacitor | Japanese Polymer Capacitor |
| Impedance/ESR | 0.012 Ohm at 100kHz/16V |
| Ripple current | 5000mA rms |
| Choke | German Common-mode Choke |
| Series resistance (DC) | 0.205 Ohm/path |
| Wire / trace thickness | twisted 22 AWG / 32 mils |
| Operating temperature | -40 °C to +105 °C |
| Dimensions | 37.7 L x 8.8 W x 14.5 H mm |
| Weight | 8.1 grams (inc. JST connectors) |
Note:, It is now possible to select between common mode and single mode filtering. A solder jumper pad on the input side disables filtering on the negative/ground-lead. If you experience issue with OSD systems, try changing the filter to single mode., Specifications:,
Details This small LC Power Filter is a must have ...GetFPV
QAV400 POWER DISTRIBUTION BOARD
This is the power distribution board for the QAV400 FPV Quadcopter frame. This PDB removes the possibility for electrical shorts. Weight: 36.5g,
DetailsGetFPV
QAV500 POWER DISTRIBUTION BOARD V1.1
This is the new and improved power distribution board version 1.1 for the QAV500 FPV Quadcopter frame. This version of the PDB removes the possibility for electrical shorts a few users have experienced. Weight: 55g,
DetailsGetFPV
QAV400 POWER DISTRIBUTION BOARD
This is the power distribution board for the QAV400 FPV Quadcopter frame. This PDB removes the possibility for electrical shorts. Weight: 36.5g,
DetailsGetFPV
QAV500 POWER DISTRIBUTION BOARD V1.1
This is the new and improved power distribution board version 1.1 for the QAV500 FPV Quadcopter frame. This version of the PDB removes the possibility for electrical shorts a few users have experienced. Weight: 55g,
DetailsGetFPV
FATSHARK FILTERED BALANCE LEAD POWER SUPPLY
,
Details Supplying power to your TX/camera is a snap with ...GetFPV
PRO TRICOPTER POWER DISTRIBUTION BOARD & FRAME PLATE
,
Details This is a power distribution board for the Pro ...GetFPV
PRO TRICOPTER POWER DISTRIBUTION BOARD & FRAME PLATE
,
Details This is a power distribution board for the Pro ...GetFPV
PRO TRICOPTER POWER DISTRIBUTION BOARD & FRAME PLATE
,
Details This is a power distribution board for the Pro ...GetFPV
FATSHARK 2P MOLEX/2P RC TX POWER CABLE
,
Details This is a replacement power cable for the ImmersionRC ...GetFPV
AC/DC POWER ADAPTER 12V 1.0A
| Center | Positive |
Barrel Connector Size:, 5.5mm (Outside barrel) x 2.5mm (Inside Barrel),
Details This is a 12v 1.0 amp power adapter. This ...GetFPV
XT60 POWER CONNECTORS (5 PAIR)
,
Details Made from high-temp Nylon and gold plated spring connectors, ...GetFPV
DJI NAZA-M V2 POWER MANAGEMENT UNIT
,
Details Independent PMU with amazing function extension The Naza PMU ...GetFPV
TIGER MOTOR U8-16 100KV U-POWER PROFESSIONAL MOTOR
| No load current | .6A/22.2V |
| Max Watts/Time | 750W/180s |
| Max Amps/Time | 24A/180S |
| Resistance Ohm | 186m |
| Case Height/Length | 86.8x26.5mm |
| Weight | 240g |
| Recommended ESC | 30amp-40amp |
| Recommended Battery Configuration | 6-12s |
| Recommended CF Prop | (T-motor style) - 26-29" |
KV: 100kv,
Details The U8 series motor by Tiger Motors is the ...GetFPV
DRAGONLINK SPEKTRUM/JR TX CABLE WITH POWER PLUG
,
Details Spare/replacement cable to connect a Dragonlink V2 to a ...